If you’ve ever wanted to build a set of regulation cornhole boards but weren’t sure where to start, this blog post is for you! In just 5 simple steps, you’ll have your own cornhole boards that meet all the regulations for tournament play. We’ll guide you through the entire process, from gathering the materials to the finishing touches. So grab your tools and let’s get started on building your own regulation cornhole boards!
No products found.
What is Build Regulation Cornhole Boards?
Have you heard of the game of Cornhole but aren’t sure what it is? Cornhole is a fun outdoor game that is easy to learn and play. Not only is it a great way to have fun with family and friends, but it can also be used for competition. If you’re looking to get serious about the game, you’ll want to make sure your Cornhole boards are regulation-sized. In this blog post, we’ll explain what build regulation Cornhole boards are and why it’s important for competitive play.
DIY Corn Hole Board Project
Cornhole is a fun, classic game that can be played both indoors and outdoors. Building regulation cornhole boards is a great way to start your own set and add a personal touch to your game. It’s not as hard as you may think to make a set of boards that meets all the necessary regulations – here are five easy steps for building regulation cornhole boards.
1. Gather Materials: Start by gathering the materials needed for the project, such as two sheets of plywood, wood screws, wood glue, clamps, saw, drill and drill bit, sandpaper, ruler, spray paint, and a small bag of corn filled bags.
2. Cut the Plywood: Next, use the saw to cut two pieces of plywood measuring 24 x 48.
3. Assemble the Frame: Use the wood screws and wood glue to assemble the frame of the board. Start by connecting two edges of each piece of plywood together using screws. Repeat this process for the other two edges to form a rectangular frame.
4. Drill Holes: Now it’s time to drill holes for the bags to enter through. Using a drill and bit, measure 4 inches from the outside edge of the board and mark the spot. Drill two holes centered on this mark; one at 4 inches from the top edge and one at 4 inches from the bottom edge.
5. Finish and Paint: Sand down any rough edges and finish off with your choice of paint or stain. Now you have a completed regulation size cornhole board!
Making your own regulation size cornhole boards can be a fun and rewarding project that the whole family can get involved in. And if you follow these five easy steps you’ll have a set of regulation size boards in no time!
Official Dimensions of Cornhole Boards
Are you looking to build your own set of regulation cornhole boards? Before you begin, it is important to make sure your boards meet the official dimensions and specifications. The American Cornhole Association (ACA) sets the standard for cornhole boards and requires all boards used in their tournaments to adhere to their rules.
The official dimensions for cornhole boards are 48 long by 24 wide and the surface should be a 1⁄2 plywood. The playing surface should be 2’ from the ground. The hole cutout should be 6 in diameter and centered 9 from the top of the board. The sides of the board should extend at least 6 past the hole and should be 1 1⁄2 high.
It is also important to remember that all boards must be painted or stained before use. While there is no official color requirement, it is recommended that one side of each board is painted with a solid background color, such as white, red, black, or blue. The other side should have a contrasting trim color and the hole should be painted a solid color. This helps create an even playing field between the two teams.
By making sure your boards meet the official dimensions and specifications, you can ensure that you have a quality set of cornhole boards for hours of fun. With these tips in mind, you can now move on to the next step of building your cornhole boards!
Materials You Will Need To Build Regulation Corn Hole Boards

Building regulation cornhole boards is a great way to add a bit of fun to your outdoor entertaining space. Whether you plan to use your boards for friendly tournaments or for some leisurely tossing, building your own regulation cornhole boards is an enjoyable and rewarding project.
To get started, you’ll need the following materials:
1. Two pieces of 48 x 24 3⁄4-inch plywood – these will serve as the tops and bottoms of your boards.
2. One 8-foot 2×4 – this will be used to create the sides of the boards.
3. One 4-foot 2×4 – this will be used to create the support beam in the middle of each board.
4. A box of 1 1⁄2-inch wood screws – these will be used to attach the boards and sides together.
5. A bag of cornhole bags (or any other type of bag game you prefer) – these will provide hours of fun!
6. Exterior grade paint or stain – use this to customize the colors of your boards and give them a unique look.
7. Sandpaper – use this to smooth out any rough edges that may have been created during construction.
Once you have gathered all of the necessary materials, you are ready to start building your regulation cornhole boards. Follow the steps below for a successful project:
1. Cut the 2x4s into four equal lengths – two 18-inch pieces and two 12-inch pieces.
2. Assemble the frame by screwing the two 18-inch pieces together into an L shape and then securing the two 12-inch pieces between them to form a rectangle.
3. Screw the top and bottom plywood pieces to the frame.
4. Add the support beam in the middle of each board by screwing it into the four corners of the frame.
5. Paint or stain the boards in your desired colors, making sure to let them dry thoroughly before adding any bags.
And there you have it – regulation cornhole boards built in five easy steps! With these steps, you can easily create your own boards and have some fun with friends and family in no time at all.
Step-By-Step Guide To Make Cornhole Boards:
1) Cut the plywood

Building regulation cornhole boards can be a fun and rewarding project, but you need to make sure you do it right in order to get the full experience of playing. To make sure you create your boards to the regulation size and shape, here are the steps to follow when cutting your plywood.
First, measure and mark out two pieces of plywood that measure 48 inches by 24 inches. Once you have the two pieces measured and marked, use a circular saw or jigsaw to cut them out. Make sure to keep your lines as straight as possible, as this will ensure that your boards look professional.
Next, mark the 12 inch circles in the center of each board. Use a compass to make sure the circles are even, and then cut the circles out with the same tool you used for the rectangles. Be careful when cutting the circles, as this is an important step for creating regulation-sized boards.
Once you have the circles cut, measure 6 inches from the edge of each circle towards the center of the board, and mark a line. Then, cut along the lines with your saw to create the 6 inch hole that is necessary for regulation play.
Finally, make sure to sand down all of your cuts, and you are ready to paint or stain your boards! By following these steps, you will have created two regulation-size cornhole boards that are ready for a great game.
2) Assemble the frame

Assembling the frame of your regulation cornhole boards is a key step in the process. You will need a saw, drill, screws, wood glue, and your wooden boards.
Start by cutting your 2×4 boards into four pieces. Each board should be 24 inches long. Next, attach the 2×4 boards together to create a rectangle frame with the outside measurements of 48 inches long and 24 inches wide. Make sure all the corners are square and use wood glue along with screws to secure them.
Once the frame is assembled, place the plywood on top of the frame. The plywood should be 48 inches long and 24 inches wide. Secure the plywood to the frame using wood glue and screws.
Now that your frame is complete, you can move on to building the legs for your regulation cornhole boards.
3) Add the support

Building regulation cornhole boards can seem like a daunting task, but with the right materials and a few easy steps, you can have a set of professional-quality cornhole boards in no time. In this section, we’ll discuss how to add the support to your cornhole boards.
First, you’ll need to purchase the support for your boards. Regulation cornhole boards require two supports on each board—one for each side. You can buy pre-made supports, or you can make them yourself. If you choose to make them, you’ll need four two-by-fours cut to 36 inches each. Sand down any rough edges before proceeding.
Next, attach the supports to the boards. Drill pilot holes into the boards and use screws to secure the supports in place. Make sure the supports are level and the screws are tight.
Finally, add a finish to the boards and supports. You can use paint, stain, or any other kind of sealant you’d like. Once everything is dry, you’re ready to start playing some regulation cornhole!
4) Attach the legs

If you’re looking to build your own regulation cornhole boards, the first step is to attach the legs. The most common type of legs used for regulation cornhole boards are 2x4s cut to 12 inches in length. Start by attaching the two legs together using two 2.5 inch screws at each end. Once both legs are secured together, attach them to the frame with four more 2.5 inch screws. Make sure to countersink the screws so they are flush with the top of the frame. You can use a drill bit slightly larger than the head of the screw to help create the countersink. To ensure a secure fit, predrill pilot holes before inserting the screws.
5) Add the finish

Adding the finish to your regulation cornhole boards is the final step in making sure that you have created a great set of boards for your next game. Here’s what you need to do:
1. Sand down the board: The first step is to make sure that the board is sanded down with some medium-grit sandpaper to remove any rough spots or splinters that may be present. Make sure to go over the entire surface, paying special attention to the edges of the board where it can be more prone to splintering.
2. Clean off the board: After sanding, use a damp cloth to wipe off any sawdust or other debris from the board. This will also help ensure that any paint or sealer that you apply later on will stick properly.
3. Apply primer: If you’re using a paint-based finish, it’s important to start by applying a coat of primer. This will help ensure that the paint will stick properly and will also provide an extra layer of protection against weather and wear-and-tear.
4. Apply paint: Once the primer has had time to dry, it’s time to apply the paint. Choose a color that best matches your decor and team colors, if you’re creating custom boards for a tournament. Make sure to apply two coats of paint and allow each coat to dry thoroughly before applying the next.
5. Seal the board: Once the paint has had time to dry, it’s important to seal it with a clear sealer. This will help protect the paint and make sure that it doesn’t fade or chip away over time. Allow the sealer to dry completely before using your boards.
Congratulations! You’ve now built a set of regulation cornhole boards that are ready to take on all comers! Have fun and enjoy your games!
Conclusion
Congratulations, you’ve just completed your journey on how to build regulation cornhole boards! You should now have a pair of regulation cornhole boards that you can proudly show off and enjoy for years to come.
Building your own cornhole boards is a great way to have fun with friends and family, as well as bring some friendly competition to the backyard. Whether you’re building them for yourself or as a gift for someone else, you can be sure that these cornhole boards will provide hours of entertainment.
We hope this article was helpful in guiding you through the steps of building your own cornhole boards. With a little time and effort, you’ll be ready to start enjoying your new cornhole set right away. Good luck and have fun!
FAQS
Q. What size boards should I make?
A. You can make them as big as you want, but the standard size is 4′ x 2′.
Q. Where do I buy the wood to make cornhole boards?
A. You can go to a home improvement store and get plywood or order it online at amazon, lumber liquidators, etc., and if you want a more traditional feel you can use cedar planks (2x4s work well too).
Q. How many bags of concrete will I need for regulation cornhole boards?
A. One bag per board for small boards and two bags per board for large boards.
Q. How long does it take to paint the back of my boards with primer?
A. The time depends on how thick your coats are, but expect about 3 hours per coat of primer
References & Additional Resources
- The Fun (And Competitive) Approach to Winning at Cornhole
- Spacing for Cornhole Boards – PDF
- How to Build a Cheap Wood Privacy Fence in 8 Steps
- The 5 Best Portable Generators Reviewed and Buyers Guide
Last Updated on December 20, 2022