How to Change Line on a Weedeater in 5 Steps

If you use your weed eater to trim the lawn or do weeding, there comes a point where the line will run out and you’ll need to replace it with new line. When that time comes, here are 5 steps how to change line on a weed eater so you can get back to your work as quickly as possible!

Changing the line on your weed eater doesn’t have to be hard, but there are a few things you should know before you get started. In this step-by-step guide, I’ll show you exactly what you need to do in order 5 Step how to change the line on your weedeater, so read on and learn everything you need to know about weed eaters and their lines!

Step to Change Line on a Weedeater

1) Pull the old line out of the weedeater.

1) Pull the old line out of the weedeater.

Changing the line on your weedeater is an essential part of maintaining and keeping your weedeater in good working order. Fortunately, it’s not a difficult task, and it can be done in five simple steps.

The first step is to remove the old line from the weedeater. To do this, locate the head of the weedeater and locate the spool cover. Remove the cover and locate the spool. If there is any remaining line on the spool, use a pair of scissors or a knife to cut it away. Once all of the old line has been removed, take out the spool and set it aside. Now you are ready to insert the new line.

2) Cut the new line to the correct length.

Cut the new line to the correct length.

When replacing the line on your weedeater, it’s important to make sure you have the right length. Too short and you’ll find yourself needing to cut more sooner rather than later, and too long and you’ll be dealing with tangled line and poor cutting performance. So, the first step is to cut the new line to the correct length.

To do this, measure out the length of the old line that you took off. If you don’t have access to the old line, most manufacturers will provide instructions on how much line you need for your particular model. Once you have the length, use a pair of scissors or a knife to cut the new line to the same length. Remember, a few extra inches won’t hurt, but make sure it isn’t too long!

Once the line is cut, move on to the next step: attaching the new line to the spool.

3) Feed the new line through the eyelet.

Feed the new line through the eyelet.

Changing the line on a weedeater is an easy process. It only takes a few steps to do it properly.

The first step is to feed the new line through the eyelet, which is located on the front of the weedeater. Start by carefully threading one end of the line through the eyelet. Make sure it is threaded all the way through, so that it is securely in place.

Once the line is secure in the eyelet, it’s time to attach the other end. Take the other end of the line and wrap it around the spool, making sure that the line winds in the same direction as indicated by the arrows. Then, tie a knot at the end of the line to ensure that it is securely attached.

Next, wind the line onto the spool. This can be done with your hands or by using a tool that is specifically designed for this purpose. Make sure to wind the line evenly onto the spool and not too tightly, so that it doesn’t jam up when you are using it.

After the line is wound, it’s time to replace the cap that covers the spool. This will keep dirt and debris out and prevent the line from becoming tangled when you are using it.

Finally, replace the housing that covers the eyelet and spool. Once everything is back in place, your weedeater is ready to go! You should now have a brand new line that is ready to cut your grass and weeds quickly and easily.

4) Wrap the new line around the spool.

Wrap the new line around the spool.

Changing the line on a weedeater is an easy task that can help keep your lawn looking neat and tidy. All you need is a few basic tools, some new line, and a few minutes of your time to have it up and running. Here are the five steps you need to take to get your weedeater line changed out:

  • Shut off the power to the weedeater. To ensure your safety, make sure that the unit is completely shut off and unplugged before attempting to replace the line.
  • Remove the spool. Locate the spool housing and remove the spool from it by pressing down on the tabs at either side of the spool and pulling straight out.
  • Replace the line. Cut two equal lengths of new line for the weedeater and remove any tags or tags from the ends.
  • Wrap the new line around the spool. Depending on your model, you may need to wrap the line in a counter-clockwise direction or a clockwise direction. If there are arrows printed on the spool, make sure to follow those instructions for proper installation.
  • Place the spool back in the housing and secure it. Line up the tabs on either side of the spool with the slots in the housing and press down until it clicks into place.

Now you’re ready to get back to trimming your lawn with your newly-changed weedeater line! Enjoy!

5) Test the weedeater before using it.

Test the weedeater before using it.

Before you get started changing the line on your weedeater, it’s important to test the machine and make sure it’s in good working order. Start by priming the weedeater before adding fuel. Then, hold down the primer button for five seconds and pull the start cord four times. Once the engine has been started, let it idle for a few minutes so that it warms up.

This will help ensure the engine is running smoothly and will also help prevent any potential issues with the new line once it’s installed. Make sure to keep an eye on the engine while it idles and adjust the choke as needed if necessary.

Conclusion

Changing the line on a weedeater is a simple task that can be done in five easy steps. Not only will this help ensure your weedeater continues to work efficiently, but it also keeps you safe from any potential injury. Before you begin, make sure to consult your weedeater manual for specific instructions related to your model.

After following these steps and properly replacing the line, your weedeater should be ready for use. Remember to clean out all the dirt after you are finished using your weedeater and store it safely so it does not collect dust. You may also want to check out our blog post about how to change spark plugs for lawn mowers or chainsaw if you’re looking for more helpful tips!

FAQS

Q. What is the best way to store my weedeater?

A. Place your weedeater in an open space with enough room for the unit’s cord and hose, but not enough for leaves or grass clippings to build up over time. If your storage space has a concrete floor, cover it with wood chips or gravel before placing the unit on it; this will help prevent damage caused by moisture seeping into the frame through cracks in the concrete floor.

Q. What can I do if there are no gears left on my trimmer head?

A. First remove the trimming line spool from the inside of the head and make sure that there are no kinks in any of the lines. The blades may have dulled so they need to be sharpened or replaced as well. Replace broken blades with new ones as soon as possible; old blades may snap when used repeatedly because of fatigue from being used too many times.

Q. How long should the string last on a weedeater?

A. You should change the string after about 15 hours of use, depending on how often you weedeat.

Q. What is the procedure for changing out a line in a trimmer head?

A. Remove the trimming line spool from the inside of the head and feed one end of fresh trimming line through the slot where it feeds onto the cutting blade. Then turn on your engine and run your trimmer until you see black or blue smoke coming out – indicating that all string material has been cleared away. Once completed, turn off the engine and cut off excess trimmer line leaving 1 inch extra (ensure you tie a knot at one end).

Next insert one end of fresh trimming line through each slot where it feeds onto a cutting blade ensuring both ends are even on both sides (ie: T shaped). Finally place trimming line spool back into place at its original position in neck piece or attach to machine’s shaft (not sure what is meant here), making sure both ends feed smoothly without getting caught anywhere.

References & Additional Resources

Last Updated on December 22, 2022

Related articles

The Buyer’s Guide to the Best Drill Presses

Drill presses offer considerable accuracy and power for drilling...

Sanders for Car Paint: A Comprehensive Buyers Guide

What are the different types of sanders...

The Best Nonstick Pans: A Comprehensive Buyers Guide

What are the most common types of coatings...

The Best Streaming Devices: A Comprehensive Buyer’s Guide

Streaming devices have become an essential part of our...
spot_imgspot_img
Mark Wright
Mark Wrighthttps://printerchief.com
Mark Wright is the author and editor for Printerchief, where he brings his expertise in research and the English language to life in the world of technology journalism. When he's not immersed in the world of print, he loves exploring the outdoors in Michigan and Arizona - taking long hikes, fishing and cycling along the way. Andrew is a big reader and likes to take on DIY projects around the home and garden. With a love for the great outdoors and a sharp eye for detail, Andrew has managed to bring both a sense of adventure and enthusiasm to all his work.

LEAVE A REPLY

Please enter your comment!
Please enter your name here