Maintaining your lawn mower is an important part of ensuring it works efficiently for many years. When the pull cord on your lawn mower breaks, you may be wondering how to fix it. Fortunately, replacing a pull cord is not a difficult task. In this blog post, we will provide you with a step-by-step guide how to replacing a pull cord on a lawn mower in just three easy steps. With these simple steps, you can get your lawn mower up and running in no time.
Parts of a Lawnmower Pull Cord Assembly:

If you’ve ever had to replace the pull cord on your lawn mower, you know it can be a bit tricky. But with a few simple steps and some basic knowledge of how lawn mower pull cord assemblies work, you can get the job done quickly and safely. Before we discuss the steps to replacing your pull cord, let’s review the components of a lawn mower pull cord assembly.
The components of a lawn mower pull cord assembly include the pulley, the handle, the cord, the spring, the housing and the clip. The pulley is attached to the engine of the lawn mower and is used to help pull the cord back after you’ve released it. The handle is what you use to pull the cord in order to start the engine. The cord is the flexible material that attaches from the handle to the pulley. The spring is located inside the housing and helps retract the cord when released. The housing holds all of these components together, and the clip is used to secure the handle to the housing.
Now that you know the parts of a lawn mower pull cord assembly, let’s go over the steps needed to replace your pull cord. A typical lawn mower pull cord replacement process includes removing the old wire by cutting the end off using wire cutters and sliding off the old housing. Once this has been completed, take the new wire (which is threaded through the hole in one end of the new housing) and slide it through both ends of the old housing.
Next, slide on a new snap or plastic cap at one end of wire as well as a small rubber gasket at opposite end. Then reattach your handle to housing by clipping onto small metal hooks on either side of metal bracket with pliers or needle nose pliers (be careful not to pinch wires!). When installing new snap or cap into place, make sure not to pinch any wires as this could cause an electrical hazard! To avoid accidents like this, always wear protective gloves when working around power tools!
How to Replace Worn-Out Pull Cord on a Lawnmower

Maintaining a well-functioning lawnmower is important for keeping your lawn looking great. Over time, the pull cord can become worn out, making it difficult to start the engine. Replacing a pull cord on a lawn mower is relatively simple and can be done in three easy steps.
How to Repair a Broken “Recoil Spring” on a Mower

When the recoil spring on a lawn mower breaks, it can be a frustrating task to replace it. Fortunately, with a few simple tools and steps, replacing the pull cord on a lawn mower is an achievable task. In this section of the blog post, we’ll discuss how to repair a broken recoil spring on a mower.
The first step in replacing a pull cord on a lawn mower is to remove the plastic covering that encloses the engine. This will give you access to the recoil spring.
Next, remove the screws that hold the recoil spring in place. Be careful not to let the screws fall into the engine – you’ll need them later to put everything back together.
Once the recoil spring is loose, you can use a pair of pliers to remove it from the engine. It is important to remember that different types of mowers may have differently sized recoil springs. Make sure you get the right size when purchasing a new one.
After the old spring is removed, you can then install the new spring by simply reversing the process used to remove it. Make sure you tighten all the screws securely so that the new spring can do its job properly.
Finally, replace the plastic covering over the engine and your lawn mower should be ready to go. If you’ve followed these steps correctly, you’ll have successfully replaced the pull cord on your lawn mower.
3 Reasons Lawn Mower Won’t Start – & How To Fix It
1) The Pull Cord is Stuck
Check the reason behind it stopping to retract. Is it stuck, or did it just stop retracting?
If the pull cord is stuck, remove the entire pull cord assembly and follow the steps above to remove and, if necessary, replace the pull cord.
2) The Pull Cord Won’t Retract
If the pull cord isn’t retracting, the problem is most likely the Recoil Spring. Follow our steps or the YouTube video above to learn how to rewind a lawn mower recoil spring.
3) The Pull Cord Works Fine – But the Engine Won’t Start
The problem could be you’re using old gasoline (last year’s gas or you have a bad spark plug). Easy Peasy. Remember, there are only two things required to start a combustible engine. Gas and spark
Conclusion
When it comes to replacing a pull cord on a lawn mower, it’s important to remember that a bit of planning and preparation can make the task much easier. By following the steps above, you should be able to replace your pull cord in no time. Make sure to refer to your lawn mower’s manual for specific instructions, as the process may vary slightly depending on the model of your machine.
With that being said, it’s important to keep safety in mind. Before beginning any repair or maintenance work on a lawn mower, always disconnect the spark plug wire to prevent accidental starts. Additionally, it’s wise to use protective eyewear and gloves when working with small parts or sharp edges.
Make sure you watch the videos provided before getting started; they are a great visual tutorial and might save you time and frustration!
Replacing the pull cord on your lawn mower doesn’t have to be difficult. By following the steps outlined in this article, you can easily get your mower up and running in no time.
FAQS
Q. What should I do if my cord is too short?
A. Depending on the model of your lawn mower, you may be able to replace the old cord with a new one that has a longer reach. Otherwise, you will need to purchase an extension cord for this purpose. Extension cords can be found at most hardware stores and online retailers. You will also need wire strippers and crimp connectors (to attach the new cord) in order to complete this project properly.
Q. How do I remove the old pull cord?
A. The first step in replacing a pull cord is removing the existing one from the lawn mower’s engine pulley system. To do so, turn off your lawn mower’s engine and wait until it has cooled down before touching it or attempting to disconnect any parts. Next, find where the power connection meets with the pull-cord pulley system–typically near where you would hold onto while pulling the starter rope. Once you find this spot, use pliers or other tools to remove any securing bolts or screws holding these two components together–depending on what kind of machine you have and how many different parts are involved in connecting them together.
Q. Why won’t my lawn mower start after replacing the pull cord?
A. After reassembling the power connection and securing any loose parts, try starting your lawnmower again by pulling on its starter rope as you normally would. If it does not start after following these steps, there may be a more serious problem with the engine or transmission system. If this occurs, consult our Troubleshooting Guide for tips on locating and addressing potential issues with your specific make and model of lawnmower.
Q. Does replacing the pull cord fix all problems with my lawn mower?
A. No, but it may resolve some of the smaller ones. For example, a broken pull cord could cause your blade to get stuck in place during operation; however, this symptom could also stem from issues like low gas levels or bent blades which require additional repairs. If you’re still experiencing problems after changing out your pull cord, please contact our customer service team for further assistance
References & Additional Resources
- Best Self Propelled Gas Lawn Mower- Reviews and Buyers Guide 2023
- The 5 Steps You Need to Take to Keep Grass From Sticking to Your Mower Deck
- Lawn Mower Surging Try These 6 Steps
- 5 Best Electric Corded Mower Reviews and Buyers Guide
Last Updated on December 20, 2022
Caan I juhst say what a comfort too uncover a person that
really knows what they are taking about online. Youu definitely
realize howw too brjng a prpblem tto light annd make iit important.
A lot more people should lookk at thiis and understand thiss side off the story.
I was surprised yyou aren’t moire popular because youu most certainly possess
tthe gift.